OBD_BleBox/BleCanBoxCode/NRF51802/examples/bsp/n5_starterkit.h

/*
This software is subject to the license described in the License.txt file
included with this software distribution. You may not use this file except in compliance
with this license.

Copyright (c) Dynastream Innovations Inc. 2015
All rights reserved.
*/

#ifndef N5STARTERKIT_H
#define N5STARTERKIT_H

#include "nrf_gpio.h"

// LEDs definitions for N5DK1
#define LEDS_NUMBER    4

// IO board active low leds
// N5DK1 does not define LED_START or LED_STOP since the LEDS are not on sequential pins
#define LED_A        8  //LED A on N5 Starter Kit IO Board
#define LED_B        3  //LED B on N5 Starter Kit IO Board
#define LED_C        15 //LED C on N5 Starter Kit IO Board
#define LED_D        30 //LED D on N5 Starter Kit IO Board

#define LEDS_LIST { LED_A, LED_B, LED_C, LED_D }

#define BSP_LED_0      LED_A
#define BSP_LED_1      LED_B
#define BSP_LED_2      LED_C
#define BSP_LED_3      LED_D

#define BSP_LED_0_MASK (1<<BSP_LED_0)
#define BSP_LED_1_MASK (1<<BSP_LED_1)
#define BSP_LED_2_MASK (1<<BSP_LED_2)
#define BSP_LED_3_MASK (1<<BSP_LED_3)

#define LEDS_MASK      (BSP_LED_0_MASK | BSP_LED_1_MASK | BSP_LED_2_MASK | BSP_LED_3_MASK)
/* all LEDs are lit when GPIO is low */
#define LEDS_INV_MASK  LEDS_MASK

#define BUTTONS_NUMBER 4

// IO board pull-up buttons
#define BUTTON_A     23 //BUTTON A on N5 Starter Kit IO Board
#define BUTTON_B     2  //BUTTON B on N5 Starter Kit IO Board
#define BUTTON_C     12 //BUTTON C on N5 Starter Kit IO Board
#define BUTTON_D     11 //BUTTON D on N5 Starter Kit IO Board
#define BUTTON_PULL  NRF_GPIO_PIN_PULLUP

#define BSP_BUTTON_0   BUTTON_A
#define BSP_BUTTON_1   BUTTON_B
#define BSP_BUTTON_2   BUTTON_C
#define BSP_BUTTON_3   BUTTON_D

#define BSP_BUTTON_0_MASK (1<<BSP_BUTTON_0)
#define BSP_BUTTON_1_MASK (1<<BSP_BUTTON_1)
#define BSP_BUTTON_2_MASK (1<<BSP_BUTTON_2)
#define BSP_BUTTON_3_MASK (1<<BSP_BUTTON_3)

#define BUTTONS_MASK   0x00801804 // b100000000001100000000100
#define BUTTONS_LIST { BUTTON_A, BUTTON_B, BUTTON_C, BUTTON_D }

// Battery board pull-up switches
#define SWITCH_1     5  // Switch 1 on N5 Starter Kit Battery Board
#define SWITCH_2     0  // Switch 2 on N5 Starter Kit Battery Board
#define SWITCH_3     6  // Switch 3 on N5 Starter Kit Battery Board
#define SWITCH_4     24 // Switch 4 on N5 Starter Kit Battery Board
#define SWITCH_5     9  // Switch 5 on N5 Starter Kit Battery Board
#define SWITCH_PULL  NRF_GPIO_PIN_PULLUP

#define SWITCHES_NUMBER 5

#define BSP_SWITCH_0 SWITCH_1
#define BSP_SWITCH_1 SWITCH_2
#define BSP_SWITCH_2 SWITCH_3
#define BSP_SWITCH_3 SWITCH_4
#define BSP_SWITCH_4 SWITCH_5

#define SWITCHES_MASK 0x01000261

// N5DK1 does not have UART peripheral. Dummy defines for compilation.
#define RX_PIN_NUMBER  0xFF
#define TX_PIN_NUMBER  0xFF
#define CTS_PIN_NUMBER 0xFF
#define RTS_PIN_NUMBER 0xFF

// Low frequency clock source to be used by the SoftDevice
#ifdef S210
#define NRF_CLOCK_LFCLKSRC      NRF_CLOCK_LFCLKSRC_XTAL_50_PPM
#else
#define NRF_CLOCK_LFCLKSRC      {.source        = NRF_CLOCK_LF_SRC_XTAL,            \
                                 .rc_ctiv       = 0,                                \
                                 .rc_temp_ctiv  = 0,                                \
                                 .xtal_accuracy = NRF_CLOCK_LF_XTAL_ACCURACY_50_PPM}
#endif

#endif